5
$\begingroup$

In IEEE 802.11a standards, there are many fields. Of which is the Data field which has 52 available sub-carriers used for transmission of coded bits. If the subcarrier locations are numbered from 32,-31,...0,1,...31.

I have read in the book that

that 48 out of 52 subcarriers are used for transmission of data bits. While 4 pilots are used as pilots for phase and frequency tracking and training. The pilot subcarriers are located at -21,-7,7,21 with values 1 (at -21,-7,7) and -1 at 21.

I am just wondering, usually the preamble (fields before the data field) is used to estimate the channel by sending a pilot symbol (using ALL subcarriers). Then my questions are

1) what is the purpose of sending these 4 pilot tones?

2) I am guessing phase and frequency tracking is different from channel estimations?

3) My last question is do we send the pilot values on the predefined pilot subcarriers ALONG with the data bits? so basically is each OFDM symbol made up of pilot and data tones? This is different than the procedure in preamble where ALL subcarriers are used to send one pilot symbol, right?

Thanks

Improve this question
$\endgroup$

1 Answer 1

Reset to default
4
$\begingroup$
  1. A frequency offset $f_\mathrm{off}$ between the carrier frequency and the local oscillator (at the receiver) results in a linear phase, i.e. the received signal contains a factor $\mathrm{exp}(j2\pi f_\mathrm{off}/f_\mathrm{s}n)$, where $f_\mathrm{s}$ is the sampling frequency and $n$ is the discrete time. If the frequency offset is sufficiently low (e.g. because it has been estimated and compensated for in an earlier step) the linearly changing phase can be assumed constant during one OFDM symbol. This means that all samples of the received OFDM symbol have a constant phase offset that can be estimated using the pilot subcarriers. As the phase is changing slowly, this has to be done for every OFDM symbol individually. The pilot symbols can also be used to estimate phase noise.
  2. Yes, see 1. Frequency and phase offsets are time varying effects while the channel is assumed to be constant for at least some OFDM symbols.
  3. Yes, pilot tones are sent in every OFDM symbol, along with data subcarriers.
Improve this answer
$\endgroup$
4
  • $\begingroup$ Thank you very much, you are always very helpful and clear. So basically this procedure we are disccusing pilot tones within OFDM symbols are different than the pilot symbols send out in the preamble where we use ALL subcarriers to estimate the channel ? $\endgroup$
    – Tyrone
    Commented May 28, 2015 at 15:52
  • $\begingroup$ By the way, do you mean to say i.e. the received signal is multiplied instead of i.e. the transmitted signal is multiplied? $\endgroup$
    – Tyrone
    Commented May 28, 2015 at 15:54
  • $\begingroup$ Yes, a pilot symbol is an OFDM symbol, where the value of every subcarrier is predefined. A pilot tone is an OFDM subcarrier, on which a predefined value is transmitted. These are different concepts. $\endgroup$
    – Deve
    Commented May 28, 2015 at 15:56
  • 1
    $\begingroup$ You could also use the pilot tones for timing offset estimation. A symbol timing error will result in a phase shift in each subcarrier, where the amounf of the phase shift is proportional to frequency. One could fit a line to the estimated phase error across the pilot tones to estimate any sampling phase error. $\endgroup$
    – Jason R
    Commented May 28, 2015 at 17:02

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.