We’re rewarding the question askers & reputations are being recalculated! Read more.

Questions tagged [window]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
1answer
101 views

Subsampling data: terminology

I'm writing software and the data reporting frequency is slower than the acquisition cycle, so effectively sub-sampling is being done. Different data types require different methods of sub-sampling ...
0
votes
2answers
350 views

Fourier Synthesis With Varying Frequencies Over Time

I'm doing some fourier synthesis by making bins of complex numbers, filling them out with the amplitude and phase information and using IFFT to turn that into time domain samples. I'm able to make ...
0
votes
1answer
370 views

Will using window in Welch's method introduce artificial peak in estimated PSD?

I'd like to estimate the power spectral density of the signal attached here, the sampling rate is 100 Hz. If I don't do windowing (i.e., use boxcar window), the result seems to be a simple $1/f^2$ ...
0
votes
1answer
20 views

Peak to Average Power Ratio of an exponentially increasing signal

I am having an exponentially increasing sinusoidal signal. After sampling, I am dividing the signal into frames of length 128 and doing windowing operation with a hanning window of length 128. Then ...
0
votes
1answer
25 views

DTFT of window function applied to input signal

$$x[n] = cos(\omega_1n) + cos(\omega_2n)$$ $w[n] = 1/N$ for $0 \leq n < N, 0$ for everything else Find the DTFT of $y[n]=x[n]w[n]$ expressed by the DTFT of $w[n]$, $W(\omega)$ I was thinking ...
0
votes
1answer
44 views
0
votes
0answers
36 views

Window function correction when using frequency domain likelihood

I was wondering if someone could tell me or point to resources which discuss what kind of of windowing corrections factors one should use when using a frequency domain Whittle likelihood for spectral ...
0
votes
0answers
32 views

what should the the output of an FIR filter (root raised cosine) look like?

I am implementing a filter that is FIR on verilog HDL ,, I understand what happen in the filter well, I mean the delay, multiply and sum, the problem that I can't imagine how can I get the desired ...
0
votes
0answers
30 views

FIR Kaiser Window Discrete Time Filter Design

Please look at Part (c) of the question. How do we know that the Filter is a Low-pass or High-pass and is the filter designed in C a multi-band-pass filter.
0
votes
0answers
36 views

Is there a window with both a lower side lobe level and higher side lobe roll of rate than Blackman

Is there a window with both a lower side lobe level and higher side lobe roll of rate than the Blackman window - even if it is poor or useless for some other reason?
0
votes
0answers
24 views

Overlap-Add for 2-dimensional windows

I understand how overlap-add works for 1-dimensional signals, but I need to do something similar in 2 dimensions. The paper at this link covers the 1D case pretty well (see p29): http://edoc.mpg.de/...
0
votes
0answers
80 views

How to know the time of my window to calculate the STFT with python knowing only the length?

I am trying to implement a work presented in an IEEE paper where they have mentioned that the STFT was performed on the signal measurements to obtain a spectrogram with no overlap window of 3 min : I ...
0
votes
1answer
28 views

identify equilibrium region after large transient

I am looking at data from a mechanical system under an unsteady load. I'm trying to find the simplest way to identify the portion of the signal once the system reaches its new equilibrium. Here's a ...
0
votes
1answer
140 views

Hamming Window LUT function

I'm working on a project where I need to generate a LUT for Hamming Window to perform a FFT. I'm using this function (doing the table with MATLAB): ...
0
votes
2answers
141 views

What happens if you apply window after filtering a discrete signal to get it back to its original length?

What happens if you filter a discrete bandpass signal of length $N$ with a bandpass filter(Hann truncated sinc) of length $L$ and apply a window of length $N$ to the filtered signal of length $N+L-1$ ...
0
votes
2answers
161 views

Bandpass Filter Order vs Sample Numbers of Noisy Signal

I'm working on signal filtering in MATLAB. i wrote sample code that generate 50 Hz signal with some noisy frequency and use Kaiser bandpass filter to get only 50Hz frequency. this code work great! but ...
0
votes
0answers
138 views

Band-pass filtering on whole signal or overlapping chunks?

I am working with a signal acquired by a pulse oximeter, i.e. a device that records the change of light intensity reflected by a specific tissue depending on its blood perfusion. Since I am interest ...
0
votes
1answer
4k views

Reconstructing time domain signal with Hanning window

I am currently working on a frequency domain real-time application on a digital signal processor. Currently for one time frame of my algorithm I read in time domain data into a buffer, perform a ...
0
votes
0answers
358 views

Welch's Overlapped Method

I am measuring wind speed using a number of different anemometers. These anemometers are placed on a structure which exhibits sinusoidal motion. Thus, the signal of the anemometers contains both the ...
0
votes
1answer
4k views

Overlapping with flat-top window MATLAB [closed]

I am applying a flat-top window to signal because I am very interested in its actual amplitude in the time-domain. I have read that overlapping will improve results. I am using MATLAB and the ...
-1
votes
1answer
102 views

On-Chip DFT Engine vs Software DFT

I'm new to signal processing. I'm trying to build a network analyzer. So far I was only considering getting the output signal through a 16-bit ADC and then do its corresponding windowing and DFT to ...
-1
votes
1answer
450 views

FFT window corrupts signal

this is a newbie question. My goal is to create audio filter that cleans human speech from noise. I started with learning all about fft filters. At first I've created simple fft filter with ...
-1
votes
1answer
112 views

Should I use window or any filtering to average my data?

I have 80 seconds of data and I have to score my data by taking the average or median (or some other method) every 10 seconds. What's the best way to do this ? Should I just use a regular rectangular ...