Questions tagged [qpsk]

Quadrature Phase Shift Keying

17 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
1answer
243 views

QPSK Phase Recovery : Maximum-likelihood Vs Costa's Loop

I have implemented a QPSK Costa's loop in GNU Radio and run some BER benchmarking. All is going well. Out of curiosity, I'm trying to implement the Maximum Likelihood phase recovery shown below. For ...
2
votes
0answers
431 views

Problem in constellation diagram

In a waveform designing i am getting this type of constellation(image_attached). Can anyone please tell me why i am getting this type of constellation? this constellation is after frequency correction....
1
vote
0answers
33 views

Differential Encoding for M-PSK

Confused about a few topics w.r.t. differential encoding/decoding. First, consider the below BER curve taken from wikipedia ( https://en.wikipedia.org/wiki/Phase-shift_keying ) comparing BPSK/QPSK and ...
1
vote
0answers
143 views

GNU Radio - Bandwidth and Band Reject Filter

I am currently trying to generate a psk modulated carrier with gnu radio. Attach is an image of my flow graph. As can be seen I am generating a bit stream using the Random Source module and ...
1
vote
0answers
221 views

SOQPSK-TG pulse shaping

I'm trying to build an SOQPSK-TG signal in MATLAB/Octave. I am following this paper for formulas. I'm trying to generate a waveform for the phase, equation 2.4: Where q(t) is the phase pulse, ...
1
vote
0answers
323 views

How to calculate the doppler shift?

I am writing a QPSK receiver in MATLAB. In the transmitter part, I have generated random data using randi, QPSK modulated and pulse shaped using a RRC filter. The ...
1
vote
0answers
255 views

Unable to stabilize 8-PSK signal with self designed costas loop

I am trying to make a signal processing block which implements the costas loop to stabilize an 8-PSK signal. Here is the flowgraph with "costas_loop" being my block. My workflow is the following - <...
1
vote
1answer
2k views

DFE for QPSK in MATLAB

I need to do a DFE for QPSK simulation in MATLAB. The system consists of a QPSK signal transmitted with power = 1 which is then pulse shaped with a square raised-cosine filter. Add AWGN and a filter ...
0
votes
0answers
13 views

What is the QPSK Constellation Diagram used in LTE

I think the question is pretty straightforward. I have to do a class project that requires me to modulate a signal, and one of the steps is Quadrature Phase Shift Keying (QPSK). It is to be done in ...
0
votes
0answers
28 views

QPSK matlab/simulink Quantisation effects

I am trying to simulate the effects of quantization of an ADC on different waveforms (e.g. QPSK,8PSK) in Simulink. For the case of QPSK the default BER curve would be generated with 2 bits per symbol ...
0
votes
0answers
49 views

Nyquist sampling theorem / Nyquist - Shannon theorem evaluation over M-PSK

I am trying to simulate an M-PSK Tx-Rx System on Simulink and analyse what the effect of sampling rate reduction would have on it. More, particular I am trying to prove what Nyquist sampling theorem ...
0
votes
0answers
33 views

Learning PSK Modulation and Demodulation - Good Text to Read?

Title sums it up. I am curious to see what you all suggest. I'm a newbie and just need some beginner/intermediate material. Thanks!
0
votes
0answers
26 views

lte matlab baseband IQ recovery

I am a beginner again to signal processing, I did my degree over ten years ago, and I am relearning all my signal processing stuff. I am a software developer by trade but now I am looking at some LTE ...
0
votes
0answers
25 views

How to compare two 802.15.4 O-QPSK modulated digitals signals?

I am working on wireless sensors project and I am trying to simulate a transmission between two nodes. So let's say I have two nodes which transmit the message to each other, i.e. node 1 transmits ...
0
votes
0answers
54 views

what waveform using to send qpsk signal with IQ tranceiver

I have an SDR tranceiver (AD9361 on fmcomms3) working with IQ channels, i wanted to make a c++ software that modulate and send a digital QPSK signal but i'm a beginner in digital signal processing and ...
0
votes
0answers
613 views

Sampling rate versus number of sample of I and Q

I am acquiring data of an O-QPSK signal (chip rate : 2Mchip/s) with a SDR. I am undersampling the signal at 20 Mhz (carrier is at 2.8 GHz) so I respect the Shannon-Nyquist criterion that you need to ...
0
votes
2answers
2k views

GNU Radio QPSK 4 Symbols

I'd like to generate a simple QPSK signal in GNU radio, but so far I haven't been able to get it to perform the way I'd like and I'm not sure if this has to do with some misunderstanding I have about ...