Questions tagged [matched-filter]

Matched filter is obtained by correlating a known signal, or template, with an unknown signal to detect the presence of the template in the unknown signal.

20 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
5
votes
2answers
1k views

How to calculate the phase shift AND time delay of non-periodic signals

Say I have two non-periodic signals, $f_1(t)$ and $f_2(t)$, with Fourier transforms $F_1(\omega)$ and $F_2(\omega)$. Basically, I need to line up $f_1(t)$ and $f_2(t)$ as close as possible, and I am ...
4
votes
0answers
150 views

Discrete-time model of 2-user CDMA system, recovered information at receiver using polarity detection?

I have discrete-time model of 2-user CDMA system with: $b_1=-1, b_2=+1, \alpha_1, \alpha_2, s_1, s_2$ and $n$ white noise. What are the recovered infromation bits for user 1 and user 2 respectively ...
2
votes
0answers
37 views

Blind TDOA Estimation

I am not EE or DSP engineer, however I am working on a project that uses TDOA estimation for location finding. I am able to get the localization algorithm working using cross correlation to estimate ...
2
votes
0answers
477 views

How to eliminate matched filter background?

The question My goal is to detect an unknown frequency $f_1$ with a mixer and a matched filter. My simulation shows (below) that I correctly identify the 50 kHz external signal - but it also ...
2
votes
0answers
165 views

Signal rescaling

Please help me out with this one. I think I've been given an impossible task. I'm working on a system that transmits an active signal and looks for strong reflections. The transmitter is actually ...
1
vote
0answers
31 views

Question about relationship between aliasing and matched filter

while I was reading J. Barry's textbook (https://www.springer.com/gp/book/9780792375487), page 308 says the following: "... symbol-rate sampling at the matched filter output is generally at less ...
1
vote
2answers
95 views

How to detect a signal while ignoring another signal which is a phase shifted version?

I have a signal coming from a sensor as shown below. This signal has high frequency noise (as can be seen from small fast wiggles) and four regions of interest where distinct spikes can be seen. The ...
1
vote
0answers
289 views

Frequency Domain Variant of Pearson's Sample Correlation Coefficient?

Suppose that you need to find (i.e. acquire) $x_1$, a short data packet with a known bit sequence preamble (i.e. a PRBS BPSK), in $x_2$, quantized samples recorded from the output of an ADC. You don'...
1
vote
0answers
525 views

Noise covariance matrix

I am attempting to implement a generalized least squares estimator that uses a noise covariance matrix from measured data. The basic model is as follows $$\hat{c}_{GLS} = \left(\bf{A}^T\bf{\Sigma}^{-...
1
vote
0answers
413 views

Audio - TDOA and $\tt xcorr$, find the 'best' peak

I try to locate a mobile device using multilateration. The mobile device acts as the receiver and in the room I have three speakers. To calculate the position I need the time difference of arrival (...
1
vote
0answers
616 views

Moving signal power normalization

I am using matched filters using GNU Radio to extract from noise a CW Morse signal. The filter actually performs pretty well in various SNR environments. My problem is that the threshold upon I decide ...
1
vote
0answers
125 views

Should I normalize my input vector when using a matched filter?

I am using a matched filter to recognize an audio sample within a noisy input stream by cross correlating my sample with the input array and checking if the maximum crosses over my threshold. ...
0
votes
0answers
53 views

How do you perform range compression of SAR data on a 2D matrix?

I am building a Matlab program to process RADARSAT-1 data that came with this book. The book describes the steps to creating SAR image as follows I am currently implement the range compression step. ...
0
votes
1answer
157 views

phase offset extraction using matched filter

I'm looking for an application of detecting the drift of a received signal carrier frequency from ADC clock of the receiver (in case of no drift, ADC clock should be optimally an integer multiple of ...
0
votes
1answer
116 views

how to understand the MIMO zero forcing as a bank of decorrelators?

I am studying the zero forcing as a simple linear receiver for MIMO detection. according to following notes: http://www.ee.ic.ac.uk/bruno.clerckx/All.pdf. The zero forcing can be understood as the ...
0
votes
0answers
122 views

Designing Matched Filters on Arduino

I'm trying to develop a prototype at the moment that includes a sensor to detect how fast someone is typing on a keyboard. Essentially this sensor is a microphone that will be able to detect keyboard ...
0
votes
0answers
144 views

Find a simple sine wave buried within noise, FFT or cross-correlation?

My recorded signal x = s + v, where s = A*sin(ωt) and v = noise. SNR < 1 or ~ 1. So the sine wave is buried under a lot of noise. I need to compare the relative amplitudes of s for each recording ...
0
votes
0answers
207 views

Determining signal using Optimal receiver(Matched filter)

I'm given a signal that has been passed through a noisy channel using binary polar signaling with a pulse value of p(t) = 1. The receiver is coherent and the length of each pulse (in samples) is 10 ...
0
votes
0answers
95 views

Digital Communications block diagram question

I am new to digital communications and trying to understand the basic underlying concepts of digital comm systems. So far , studying the course , I have some questions which if anyone can answer would ...
0
votes
0answers
459 views

Matched filters

Working on my communication class right now, and I'm having a bit of a problem with the matched filters. As I see it the matched filters "eliminate" some of the noise. We project the received signal ...