Questions tagged [group-delay]

The tag has no usage guidance.

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
0answers
79 views

Interpretation of instaneous time and instaneous frequency in time-frequency plane?

In this paper: Sparse time-frequency representations, Given signal $x(t)$, the time-frequency representation was got by Gabor transform and was denoted by $\chi(t,\omega)=|\chi(t,\omega)|\exp(\mathrm{...
2
votes
0answers
62 views

How do large tap counts effect FIR Filters for block data?

I am using the ARM CMSIS DSP library for a signal processing application. I find good filter performance when using tap counts that are in excess of 10% of the length of my data block. I understand ...
2
votes
0answers
84 views

Stability of filters with negative phase delay, group delay, and positive phase

Lets assume I have an IIR filter with : bz = [1.0195 0 0]; az = [1 0.0166 0.0020]; fvtool(bz,az) The filter is stable as i can see. If you check the phase delay ...
2
votes
2answers
503 views

How to compare many bandpass filters (for their signal propogation delay)?

Let's say we have an audio signal sampled at 96 kHz, and we want to compare several bandpass filters to find the one with the lowest rectangular-envelope-propagation-delay (see graph below). The band ...
2
votes
1answer
315 views

How to obtain a meaningful group delay graph using matlab

Problem: I'm trying to analyze the behavior of an FIR filter with the following impulse response/kernel: Using Matlab's function grpdelay(myKernel,length(myKernel)), I obtained the following figure:...
2
votes
0answers
171 views

How to design all-pass filter by specifying phase requirements?

I want to delay the part of signal above (or below) specified frequency, but I don't find any books or tutorials to tell how to design is. The commonly used biquad APFs (such as the one introduced in ...
1
vote
2answers
231 views

Measuring group delay through a linear phase filter

I'm having a difficult time wrapping my head around a phase/ group delay problem and it corresponding to where you start sampling so I built up a system to test some of these issues. The system passes ...
1
vote
0answers
60 views

How to initialize shift registers in polyphase filter based resamplers to avoid or compensate for group delay?

I have a signal a = [a(t0),a(t1),a(t2),..,a(tN-2),a(tN-1)] I'm using a polyphase filter based resampler with filter length $L$ of $8$, fixed interpolation rate $I$ of $10000$ and decimation rate of $...
0
votes
0answers
31 views

Audio crackles with delay in series

I am learning to write audio plugins using VST3 sdk. I have an issue implementing 2 delays in serie, the audio starts crackling. Here is the processing code: ...
0
votes
0answers
55 views

Matlab group delay not corresponding to reality

I studying effects of digital filters group delay (IIR). In Matlab there is a function grpdelay which allows for particular frequency get a value of delay in samples But after filter applying and ...
0
votes
0answers
37 views

Estimation of Group Delay from Noisy Frequency Response Measurements

Consider a linear, time-invariant system. Noisy measurements of the magnitude and phase associated with the frequency response of the system are available over some dense generally non-uniform grid ...
0
votes
0answers
68 views

The grid frequencies In the design of a digital filter

I want to find many difference 'h' with same group delay and length filter using this code : https://gist.github.com/mattdsp/17f508d2b368db61f47689e4622d8841/c1518f22a5aa451951601b56c5d9f72743868bfe ...
0
votes
0answers
1k views

All pass filter design for group delay compensation

I've designed an IIR bandpass elliptic filter in Scilab with the following parameters. Sampling Frequency = 25000 Hz Lower cutoff frequency = 100 Hz Upper cutoff frequency = 150 Hz Pass band ripple = ...
0
votes
0answers
783 views

IIR filter group delay

I've designed an IIR bandpass elliptic filter in Scilab with the following parameters. Sampling Frequency = 25000 Hz Lower cutoff frequency = 100 Hz Upper cutoff frequency = 150 Hz Pass band ...
-1
votes
1answer
77 views

average linear phase (group delay)- how can be calculated, given a signal samples at frequency F?

Average linear phase (group delay)- how can be calculated, given a signal samples at frequency F? The definition doesn't help since the frequency is constant: $-[signalPhase(n)-signalPhase(n-1)]/[...