Questions tagged [digital]

The tag has no usage guidance.

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
1k views

Simple (Arduino) digital butterworth filter : why do I see oscillations?

I want to filter deviations from an ADC over time (low pass), not very critical. So I first tried exponential averaging, something like y= (7*y+x)/8. That gave useful results, but there is an obvious ...
1
vote
1answer
43 views

phase response of an analog filter

I am trying to understand the relation between phase response of an analog filter and its influence on the quality of a signal with PSK modulation. For example I want to design a BPF for HF ...
1
vote
0answers
65 views

Noise Shape Digital Filter

My objective is to build a noise shape filter from a given transfer function (in one case) and from a given PSD (for another case). Checking my precedent questions you can see that this argument is ...
1
vote
0answers
88 views

Processing digital sound in Audiokit to sound like the 1960's

I am looking to imitate 70's analog equipments sound. I was wondering is there a way to create tape saturation / distortion inside Audiokit? I want to add that and randomized tape crackles and ...
1
vote
0answers
70 views

Find another cosine y(t), whose frequency is as close as possible to that of x(t),

I am going to be straight forward and say this is one of the problem sheets and I am stuck on one of the questions. I already know the answer as I have been given them but I am trying to work ...
1
vote
1answer
142 views

Modulating ofdm in audio spectrum

Trying to modulate audio with OFDM data. My fs = 44.1khz, i'm using 64 sub-carriers, but i'm only using 5 sub-carriers for data, so my bandwidth is about 3.445khz. I'm not sure how to properly write ...
0
votes
0answers
29 views

For an LTI system, the zeos and poles are defined in the z plane. How to add additional poles and zeroes so LTI system is real valued?

The question already has a zero and a pole in the complex plane. It is asking to add additional zero and pole so LTI becomes zero valued. zeros=-1/2 + 1/2 i , poles = -1/3 -1/3 i . What I understand ...
0
votes
0answers
12 views

Computing White Speckle Metric in a Document Image

The paper 'Metric-based No-reference Quality Assessment of Heterogeneous Document Images', discusses about measuring the quality of characters in a document image. I'm having difficulty to understand ...
0
votes
1answer
56 views

Digital beamforming and phase shift stage insertion

I have read some literatures about the different topologies of beamforming and it came to my mind a question : where is applied the phase shift for each channel depending on the type of topology/...
0
votes
1answer
63 views

Carrier and timing offset

Assume my reference is 1 ppm so if my transmit frequency is 400 MHz and symbolrate is 100 kHz. Then, my carrier will have +/- 400 Hz offset and then my symbol will have +/-0.001 Hz offset. Similarly,...
0
votes
0answers
22 views

Hardware that Mixes Two Digital Audio Source into One

Is there any off-the-shelf hardware that extracts two digital audio streaming source from two digital audio stream(like USB+SPDIF), mixes, and transmits in single digital stream real-time(if the ...
0
votes
1answer
65 views

digital phase lead algorithm

I have two sine signals A and B which are simultaneously sampled at 2500 Hz using ADC. Through oscilloscope, I find that signal B lags A by about 5 degrees. I would like to digitally lead signal B to ...
0
votes
1answer
120 views

confusion between frequency and amplitude in digital to analog and vice versa conversion

bandwidth is defined as the difference between the highest frequency and lowest frequency. amplitude is the distance between the, let's call it a crest and a trough, in a wave. cycle is the time per ...
0
votes
0answers
156 views

How can I convert a FM discriminated signal to binary data using software

I currently have FM discriminated data in a .wav file. How can I convert it to binary data (+0.5 == high bit, -0.5 == low bit) given a baud rate.
-2
votes
1answer
46 views

Find $X_s(f)$ of a sampled continuous signal

I've been trying to find the transform of the following signal, but have not been successful, any help would be greatly appreciated: Find $X_s(f)$ of the following signal the "mathematical DAC" ...