Questions tagged [decimation]

Decimation is a technique for reducing the number of samples in a discrete-time signal.

Filter by
Sorted by
Tagged with
4
votes
2answers
1k views

Difference between Sub Sampling and Down Scaling of Images

I know that there are many ways to upscale (interpolate) an image using bilinear, bicubic, sinc... Somehow, these same algorithms can also be used to downscale an image. But when it comes to ...
1
vote
1answer
3k views

MATLAB: Decimation image

I'm trying to decimate given picture Vertically. Horizontally. Horizontally + Vertically. I know that I should use low-pass filter* and then downsample** it not to see any aliasing in image. To this ...
1
vote
2answers
6k views

Selecting the Low Pass FIR Filter, Decimation, DSP

I'm studying DSP, but I have weakness about it. I was reading this: http://www.eetimes.com/document.asp?doc_id=1275556 But, I don't know how select the Low Pass Filter. I am assuming that this ...
0
votes
1answer
197 views

sampling a signal below nyquist rate

This question is for people working in multi rate signal processing. Using compressive sensing techniques, we can still recover a signal by sampling below nyquist rate(by decimating the signal). How ...
0
votes
2answers
471 views

up down sampling and low-pass filters

I am trying to figure out what seems very trivial thing about down sampling and up sampling. The problem that I am facing is how to find the effects of up sample on a signal followed by a filter and/...
1
vote
0answers
112 views

Filtering and decimating input as sections in multiple stages

What would be my options to decimate a large input signal available only in sections (or blocks) due to DMA type of interface? The FIR should be about order of 18 only and the total decimation factor ...
1
vote
3answers
561 views

Upsample / Downsample a Signal from 1920.93Hz to 1920Hz [duplicate]

I've just learned that the A/D converter I am using is not sampling at my desired sampling rate. I request 20 seconds of data at 1920Hz and I receive 38400 points of data that were actually sampled ...
0
votes
2answers
1k views

FIR-Decimation and Low-pass filter (taps vs number of input points vs number of decimation stages)

I am new to digital filters and trying to understand parameters behind them. Scenario I am trying to get DC value from signals sampled at 100kHz sampling rate. such high frequency is used due to ...
2
votes
1answer
956 views

IIR/FIR filtering before decimation?

I am trying to design a low pass filter to apply before resampling the sensor's output at a lower rate, however I am not quite sure how to choose between the IIR and FIR fitlers. Matlab by default, ...
2
votes
1answer
1k views

Polyphase decimation matlab [closed]

I am new to DSP, and currently trying to implement a simple polyphase decimation program in matlab. M is decimation factor, x is input (for now it is a square wave 8096 samples), y_polyDec is result ...
3
votes
7answers
6k views

Downsampling/Decimation - When is well done?

I am working on decimation of signal, and I want to know which is the best way to understand if the downsampling is well done or not. At the moment I am comparing the FFT of the source signal and the ...
1
vote
0answers
258 views

Symbol timing recovery algorithms

I am trying to implement the symbol timing recovery loop and for that I have chosen two algorithm to compare my results one is feedforward and Gardner TED. One thing that is confusing me is smoothing ...
1
vote
0answers
713 views

What is the output sequence of a Decimation filter [closed]

Consider x(n) as input, y(n) as output & h(n) as filter coefficient. The filter is of 16 taps(N=16) from 0 to 15. The decimation factor of the filter is 4. When I apply x(n) to this 16 tap ...
1
vote
1answer
3k views

CIC Filter vs Simple Downsampler

I' trying to implement a QPSK modulation/demodulation. At one point I have to decimate my signal by 4 for an easier implementation. I've read everywhere that the best way to do it is to use a CIC ...
1
vote
0answers
213 views

RLS adaptive filter

I am using an adaptive RLS adaptive filter for noise cancellation. My sampling freq. is 500 Hz, but I am interested in only frequencies of up to 60 Hz. I filter the input and the reference signal to ...
0
votes
2answers
2k views

Decimation of signal. How to plot frequency spectrum

I have an FDM signal from 0 to 70 MHz. The total signal contains 4 FDM signals from (0-fs/4), (fs/4-fs/2), (fs/2-3fs/4) & (3fs/4-fs). I used fvtool command in matlab to plot these signals. Then i ...
2
votes
2answers
246 views

Decimating a discrete time cosine function

Let $x[n] = \cos(wn)\ \ $ be our signal. Let the other signal be $x_2[n] = \cos(2wn)\ \ $ . The spectrum of $x[n]$ and $x_2[n]$ are well defined and consist of impulses at the relevant frequencies ...
12
votes
1answer
11k views

Downsampling a signal with decimate

I'm experimenting with decimating a signal, in this case a unit impulse. I'm using Python, with pylab. First, I create a unit impulse, and decimate it by 5. ...
4
votes
1answer
900 views

Timing syncronisation using polyphase decimation filter

This question is regarding application of polyphase decimation filter in symbol time correction. How does choosing a perticular "polyphase branch" in a polyphase decimation filter result in timing ...
4
votes
2answers
4k views

Design of the low pass filter when decimating

I am filtering an audio signal into various sub-bands in C and would like to decimate the signal by 2 in the lower frequency bands to reduce processing overhead. I get that this involves low-pass ...
4
votes
3answers
637 views

Image Pyramid Without Decimation

I have an image processing algorithm which uses Gaussian and Laplacian Pyramid Decomposition. At each level of the pyramid the algorithm decimates the previous level by a factor of 2. The LPF the ...
21
votes
5answers
3k views

Why would I leave a signal oversampled?

I can't think of a better way for asking this question so I will start with an example. Suppose that I have an input signal with a max frequency of 50Hz (sampled at 100Hz). Now the signals of interest ...