Questions tagged [analog-to-digital]

An analog-to-digital converter (ADC, A/D, or A-to-D) is a system that converts an analog signal into a digital signal.

26 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
0answers
53 views

Proper way to implement a decimation

I have an input signal with bandwidth 2.5 MHz. Let's say it's filtered using analog Butterworth low-pass filter. I would like to sample the signal using AD9203 10-bit 40 Msps ADC. If I understand ...
2
votes
2answers
322 views

How to adjust receiver gains to avoid saturation and quantization noise to optimise post digital processing?

I am using a Hack RF One as SDR and the software GNU Radio to receive and process signals emitted from a drone. Given that the drone is moving and is emitting signals from a wide zone, received signal ...
2
votes
0answers
60 views

Modelling of quantization noise with logarithmic steps

I have to modell the quantization noise of ADC. I only know that the maximum relative error is 1 dB. Since this is logarithmic, I find it hard to formulate an appropriate model for the quantization ...
2
votes
2answers
509 views

Modeling ADC in Active Noise Cancellation

I'm tinkering in Matlab with a problem that's very similar to active noise cancellation. In the literature, the secondary path is described as the transfer function from the output of the adaptive ...
1
vote
0answers
28 views

synchronize adcs with neuronal network

if i have two adcs(analog to digital converters) sampling a signal. Is it possible to synchronize the two adcs with deep learning? as far as i know, with super-resolution on image processing it is the ...
1
vote
0answers
64 views

What is the minimum and maximum cutoff frequencies for the antialiasing filter for this ADC?

https://www.analog.com/en/products/ad9675.html https://www.analog.com/media/en/technical-documentation/data-sheets/AD9675.pdf It says in the data sheet that the Anti-Aliasing Filter has : "...
1
vote
0answers
77 views

Moving average and linearization of two piecewise linear systems

I have 2 oversampling ADC's running parallelly, each to process data in a specific range of the input as shown below: Each ADC can process only half cycle range of a sine wave. Each ADC adds its own ...
1
vote
1answer
465 views

Are resolution increase and noise reduction from oversampling mutually exclusive?

Oversampling a signal means sampling it with a significantly higher sampling frequency than the Nyquist rate. As far as I know, there are three advantages: Easier design of anti alias filter Increase ...
1
vote
0answers
179 views

ADC sampling rate in OFDM baseband processor

I have optical OFDM baseband TX and RX implemented in FPGA. The design is tested using one FPGA board in loopback connection from DAC to ADC via coaxial cable. It works fine, the BER is about 1.10^-8 ...
1
vote
0answers
79 views

Usage of a TI DSP EVM and ADC card

I'm not quite sure if I can ask about a vendor-specific hardware here, please teach me if not. We have a TI's DSP EVM, one of EVMK2Ls (XEVMK2LX/XTCIEVMK2LX) and wanna do some digital signal ...
1
vote
0answers
23 views

'ADC' sort of conversion method to retain information

I have a program that reads 16 bit two's complement format data to plot/analyze graphs. I have a database text file with various decimals which represent real analogue data, ie. let's say they are ...
1
vote
0answers
56 views

Sigma Delta Sampling

I am using a Sigma Delta ADC and really understood the working of it I need to sample a signal at 8.5 Mhz. The SD ADC has a Demodulator and decimating FIR filter The Oversampling ratio options are 32/...
1
vote
0answers
222 views

How to choose sampling rate?

I am working on a FMCW radar and I want to sample the I/Q signals from the 2 receiving antenna (total 4 channels) simultaneoulsy and send the digital data to computer to extract range and velocity ...
0
votes
1answer
21 views

Multisampling of an ADC channel in a PWM cycle in TI C2000

I want to sample an ADC channel multiple times in one PWM cycle. I can trig any ADC channel in anywhere in my PWM timer counter now. But I want to trig and sample same channel in many times within a ...
0
votes
0answers
22 views

Resources on multiplexer and demultiplexer?

If I search multiplexer in Google and start reading, I find sources that describe a multiplexer as a device that selects between several analog or digital signals, then outputs a single signal. For ...
0
votes
0answers
19 views

Threshold Estimation from a Linear FM Pulse Position Modulated signal

I have a signal chain to detect multi channel LFM (Linear Fm - Hann window being applied as shaping filter for the pulses) pulses as shown in picture below. (Numbers in the picture is in Hz., for ...
0
votes
0answers
16 views

how to do smoothing a linear noise adc signal to a exponencial curve to increase and logarithmic to decrease

I am studying methods of signal smoothing obtained in an Analog Digital converter that is operated by a common potentiometer that generates a certain noise, such potentiometer is linear and I cannot ...
0
votes
0answers
13 views

what is the DNL of flash converter

i have a flash ADC converter with 1V vref and idial ressistors but in the comparator i have standart deviation of 3mV. how do i calculate from the the standart deviation of the whole device(DNL INL)? ...
0
votes
0answers
22 views

Understanding shift in Q values?

Can any one help me understand why there is a shift in Q values? It seems there is a DC offset/bias. How do I remove it or set it accordingly to make it equal to the I values/waveform? I am using a ...
0
votes
0answers
49 views

Nyquist sampling theorem / Nyquist - Shannon theorem evaluation over M-PSK

I am trying to simulate an M-PSK Tx-Rx System on Simulink and analyse what the effect of sampling rate reduction would have on it. More, particular I am trying to prove what Nyquist sampling theorem ...
0
votes
1answer
57 views

Does FFT magnitude of recorded sound depends on the sound card used?

Based on some reading, here's my understanding of how sound recording works: Microphone outputs a voltage based on sound pressure. The microphone voltage is amplified and the amplified voltage goes ...
0
votes
2answers
527 views

Faster way to find the quantization level of a sample

Given a sequence of real numbers that represent a sound signal i.e [1.8, 2.2, 2.2, 1.9, -1.5, -0.7], we must quantize this sequence by dividing the range [-4, 4] to 32 equal parts. If we had to do ...
0
votes
1answer
177 views

Calculating filter coefficients of a Moving average with error correction

I have an oversampling ADC where I need to correct Gain/offset errors 'during' each conversion. This also links to my previous question - Moving average and linearization of two piecewise linear ...
0
votes
0answers
581 views

FFT magnitude of ADC samples, converting back to $\textrm{dBm}$

I am generating a sinusoid from a signal generator set at a specific $\textrm{dBm}$ and inputting this into an ADC as a real input (not IQ). I take a 256 point FFT on the resulting samples (raw signed ...
0
votes
0answers
397 views

DAC ADC for BPSK modulation

I have written Matlab script for BPSK modulation. The way my code works is as follow: series of 0 and 1----> NRZ data (continuous rectangular pulses with amplitude -1 and 1)--->multiply by carrier----...
0
votes
0answers
52 views

A/D converter quantization noise

I read that in A/D converter we usually use rounding or two's complement truncation and not the sign magnitude or 1's complement truncation as in this case the quantization error is correlated to the ...