Questions tagged [analog-to-digital]

An analog-to-digital converter (ADC, A/D, or A-to-D) is a system that converts an analog signal into a digital signal.

Filter by
Sorted by
Tagged with
6
votes
8answers
9k views

Nyquist Frequency Phase Shift

The figure below shows in dashed lines sinusoidal signals of the same frequency at three different phase shifts. The signals are then sampled such that the sinusoidal frequency is exactly a half of ...
1
vote
1answer
1k views

How do you simultaneously undersample and oversample?

"Undersampling" and "Oversampling" are common terms when referring to the choice of sampling frequency for analog to digital data conversion. Is it possible to Undersample and Oversample a waveform ...
0
votes
2answers
664 views

Higher order harmonics during sampling

I am studying about the sampling theorem in conjunction for ADC. I got little confused while reading about aliased frequencies. I see that as per the Nyquist theorem, the sampling frequency (fs) ...
2
votes
2answers
225 views

How to adjust receiver gains to avoid saturation and quantization noise to optimise post digital processing?

I am using a Hack RF One as SDR and the software GNU Radio to receive and process signals emitted from a drone. Given that the drone is moving and is emitting signals from a wide zone, received signal ...
9
votes
1answer
838 views

Quantization Noise for Coherent Sampling - Phase Noise?

Update: See added thoughts at bottom of this post. Under general sampling conditions not constrained by what is described below (signal uncorrelated to sampling clock), quantization noise is often ...
4
votes
2answers
2k views

How increasing the Signal to Quantization noise increases the resolution of ADC

Inside ADC we have a quantizer, when the sampled signal is passed through it, the signal values get discretized. The number of discrete levels in which the signal is discretized is called the ...
3
votes
2answers
63 views

DAC and ADC architecture in SDRs

What are the DAC and ADC architectures in SDRs for inphase and quadrature phase channels? Do we have separate ADC and DAC for each channel or there is some clever way that they are multiplexed to ...
2
votes
1answer
223 views

How to plot noise shaped spectrum of First order Incremental Sigma Delta ADC's output?

A little background: This question is about viewing the output spectrum of incremental delta sigma modulators (IDSM). IDSM is a subcategory of general delta sigma modulators where the integrators are ...
2
votes
2answers
4k views

Bandwidth with complex sampling

On the transmit side, I have a 20 MHz carrier frequency carrying a signal with bandwidth of 40 MHz (so 0 Hz to 40 MHz, center at 20 MHz). On the receive side, I have a dual channel ADC with each ...
0
votes
1answer
599 views

How can I mimic this ADC for a given resolution, sampling rate and input with MATLAB or Python?

I'm quite new to the area so I need help to progress at some point. Basically I have a signed 16 bit ADC which means it maps -10V to +10V range to 16 bit. So the max voltage +10V is 2^15-1 = 32767; ...
1
vote
1answer
314 views

Frequency measurement from acoustic emission sensor data(VDC RMS)

Currently, I am facing a problem about understanding FFT concept and getting exact frequency with acoustic emission sensor data(VDC RMS data). I want to measure the sound frequency from the acoustic ...
1
vote
0answers
73 views

Moving average and linearization of two piecewise linear systems

I have 2 oversampling ADC's running parallelly, each to process data in a specific range of the input as shown below: Each ADC can process only half cycle range of a sine wave. Each ADC adds its own ...
1
vote
3answers
833 views

Precision measurement of sine wave amplitude with ADC

I want to measure amplitude of a sine wave input precisely with a limited resolution ADC. As an example suppose that I have $1\textrm{ MHz}$ pure sine wave input to the $320\textrm{ Msps}$ $10$-bit ...
0
votes
1answer
171 views

Calculating filter coefficients of a Moving average with error correction

I have an oversampling ADC where I need to correct Gain/offset errors 'during' each conversion. This also links to my previous question - Moving average and linearization of two piecewise linear ...