Podcast #128: We chat with Kent C Dodds about why he loves React and discuss what life was like in the dark days before Git. Listen now.

Questions tagged [adc]

The tag has no usage guidance.

21 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
0answers
37 views

Proper way to implement a decimation

I have an input signal with bandwidth 2.5 MHz. Let's say it's filtered using analog Butterworth low-pass filter. I would like to sample the signal using AD9203 10-bit 40 Msps ADC. If I understand ...
2
votes
0answers
158 views

How to plot noise shaped spectrum of First order Incremental Sigma Delta ADC's output?

A little background: This question is about viewing the output spectrum of incremental delta sigma modulators (IDSM). IDSM is a subcategory of general delta sigma modulators where the integrators are ...
2
votes
0answers
59 views

Modelling of quantization noise with logarithmic steps

I have to modell the quantization noise of ADC. I only know that the maximum relative error is 1 dB. Since this is logarithmic, I find it hard to formulate an appropriate model for the quantization ...
1
vote
1answer
51 views

How to adjust receiver gains to avoid saturation and quantization noise to optimise post digital processing?

I am using a Hack RF One as SDR and the software GNU Radio to receive and process signals emitted from a drone. Given that the drone is moving and is emitting signals from a wide zone, received signal ...
1
vote
0answers
25 views

What is the minimum and maximum cutoff frequencies for the antialiasing filter for this ADC?

https://www.analog.com/en/products/ad9675.html https://www.analog.com/media/en/technical-documentation/data-sheets/AD9675.pdf It says in the data sheet that the Anti-Aliasing Filter has : "...
1
vote
0answers
52 views

Moving average and linearization of two piecewise linear systems

I have 2 oversampling ADC's running parallelly, each to process data in a specific range of the input as shown below: Each ADC can process only half cycle range of a sine wave. Each ADC adds its own ...
1
vote
1answer
240 views

Are resolution increase and noise reduction from oversampling mutually exclusive?

Oversampling a signal means sampling it with a significantly higher sampling frequency than the Nyquist rate. As far as I know, there are three advantages: Easier design of anti alias filter Increase ...
1
vote
0answers
125 views

ADC sampling rate in OFDM baseband processor

I have optical OFDM baseband TX and RX implemented in FPGA. The design is tested using one FPGA board in loopback connection from DAC to ADC via coaxial cable. It works fine, the BER is about 1.10^-8 ...
1
vote
0answers
71 views

Usage of a TI DSP EVM and ADC card

I'm not quite sure if I can ask about a vendor-specific hardware here, please teach me if not. We have a TI's DSP EVM, one of EVMK2Ls (XEVMK2LX/XTCIEVMK2LX) and wanna do some digital signal ...
1
vote
2answers
461 views

Modeling ADC in Active Noise Cancellation

I'm tinkering in Matlab with a problem that's very similar to active noise cancellation. In the literature, the secondary path is described as the transfer function from the output of the adaptive ...
1
vote
0answers
22 views

'ADC' sort of conversion method to retain information

I have a program that reads 16 bit two's complement format data to plot/analyze graphs. I have a database text file with various decimals which represent real analogue data, ie. let's say they are ...
1
vote
0answers
46 views

Sigma Delta Sampling

I am using a Sigma Delta ADC and really understood the working of it I need to sample a signal at 8.5 Mhz. The SD ADC has a Demodulator and decimating FIR filter The Oversampling ratio options are 32/...
1
vote
0answers
205 views

How to choose sampling rate?

I am working on a FMCW radar and I want to sample the I/Q signals from the 2 receiving antenna (total 4 channels) simultaneoulsy and send the digital data to computer to extract range and velocity ...
0
votes
1answer
123 views

DC Spur in DAC output

I have a design in which a signal from ADC is filtered and then played by DAC. In FPGA the real signal is converted to quadrature using DDS with 70 MHz frequency. After filtering, the baseband signal ...
0
votes
1answer
28 views

Does FFT magnitude of recorded sound depends on the sound card used?

Based on some reading, here's my understanding of how sound recording works: Microphone outputs a voltage based on sound pressure. The microphone voltage is amplified and the amplified voltage goes ...
0
votes
2answers
82 views

Faster way to find the quantization level of a sample

Given a sequence of real numbers that represent a sound signal i.e [1.8, 2.2, 2.2, 1.9, -1.5, -0.7], we must quantize this sequence by dividing the range [-4, 4] to 32 equal parts. If we had to do ...
0
votes
0answers
19 views

Resources on software PLLs in high latency systems?

For my master thesis I am prototyping a software PLL in Matlab using an Analog Devices AD9467 (ADC) evaluation+capture board. The VCO I am trying to control has an output frequency of approx. 2.2GHz ...
0
votes
1answer
132 views

Calculating filter coefficients of a Moving average with error correction

I have an oversampling ADC where I need to correct Gain/offset errors 'during' each conversion. This also links to my previous question - Moving average and linearization of two piecewise linear ...
0
votes
1answer
1k views

Realize Simulink block “Ideal ADC Quantizer” in Matlab

Yesterday I posted following topic: "FFT alternates '0' for a quantized SIN wave". During post editing I was perturbed by some affair, I didn't formulate correctly the problem. So, my post was blocked ...
0
votes
0answers
487 views

FFT magnitude of ADC samples, converting back to $\textrm{dBm}$

I am generating a sinusoid from a signal generator set at a specific $\textrm{dBm}$ and inputting this into an ADC as a real input (not IQ). I take a 256 point FFT on the resulting samples (raw signed ...
0
votes
0answers
374 views

DAC ADC for BPSK modulation

I have written Matlab script for BPSK modulation. The way my code works is as follow: series of 0 and 1----> NRZ data (continuous rectangular pulses with amplitude -1 and 1)--->multiply by carrier----...