Linked Questions

2
votes
1answer
4k views

Does Higher Sampling Rate Increase SNR?

I have AM demodulated voice samples that come from a 14bit ADC that I will filter, process, and then send to a CODEC. I can choose a sample rate of 96kSPS, 64kSPS, 48kSPS, or 32kSPS at the CODEC. ...
3
votes
1answer
6k views

What is the difference between undersampling and oversampling in analog to digital conversion ?

When converting a signal from analog to digital, we observe undersampling and oversampling. Does oversampling means that the sampling frequency is greater that the signal's frequency and does ...
4
votes
2answers
2k views

How increasing the Signal to Quantization noise increases the resolution of ADC

Inside ADC we have a quantizer, when the sampled signal is passed through it, the signal values get discretized. The number of discrete levels in which the signal is discretized is called the ...
5
votes
2answers
843 views

Increasing SNR and Dynamic Range using Oversampling

How much gain in dynamic range and SNR can be expected if we are to oversample a signal with fixed analog input bandwidth. For Example if I have a analog filter at the input which limits the bandwidth ...
5
votes
1answer
1k views

Sampling rate vs ADC noise tradeoff

I have a digital sensor that can output at two frequencies (250Hz, 1000Hz), but with different RMS AWGN noise (.35 units RMS, .5 units RMS respectively). The signal of interest has a single frequency ...
4
votes
2answers
1k views

ADC quantization +thermal noise

ADC noise can affect the overall noise performance of a receiver. The noise is partially quantization noise and partially thermal noise and as a general rule it extends up to the Nyquist frequency = ...
5
votes
1answer
3k views

How to choose FFT depth for ADC performance analysis (SINAD, ENOB)

I am trying to simulate a model of an ADC and determine its performance. One of the interesting properties is the ENOB (Effective Number Of Bits), which can be calculated from SINAD (SIgnal-to-Noise ...
1
vote
3answers
1k views

Precision measurement of sine wave amplitude with ADC

I want to measure amplitude of a sine wave input precisely with a limited resolution ADC. As an example suppose that I have $1\textrm{ MHz}$ pure sine wave input to the $320\textrm{ Msps}$ $10$-bit ...
4
votes
2answers
648 views

SNR of a 16-bit DSP with 12-bit ADC, 40-bit accumulator

According to the 6dB-per-bit rule, a 16-bit DSP would provide 96 dB of dynamic range, approximately. If the ADC and DAC are both 12-bit long, the DSP is still considered to have 96 dB, or the ...
3
votes
1answer
1k views

How do you simultaneously undersample and oversample?

"Undersampling" and "Oversampling" are common terms when referring to the choice of sampling frequency for analog to digital data conversion. Is it possible to Undersample and Oversample a waveform ...
0
votes
2answers
700 views

Compute dynamic range in a linear quantization system

I know the dynamic range is the ratio between the maximum amplitude and the minimum amplitude of a signal, calculating the dynamic range in dB I get a difference of logarithms: But why the dynamic ...
-1
votes
1answer
586 views

Difference between formula of SNR and SQNR?

Is there any difference between formula/expressionsof SNR and SQNR? where SNR is Signal to noise ratio and SQNR is signal to quantization noise . The following DSP SE question shows both SNR and SQNR ...
1
vote
3answers
208 views

confusion sampling vs quantization?

while converting analog signal to digital equivalent,we have a process that is called analog to digital conversion and it has two main steps/stages sampling and quantization? I am confused whether y ...
1
vote
1answer
464 views

Understanding the over sampling factor effects before a Matched Filter?

I am trying to design a matched filter at the receiver side to a half sine pulse shaping function sent by the transmitter of an OQPSK transceiver. I am not sure I understand the effect of varying the ...
1
vote
1answer
412 views

Oversampling while maintaining noise PSD

I'm designing a digital PID for control and stabilization of laser amplitude. The noise PSD of the laser intensity is around -140dB/Hz, and I want to servo that between DC and 100kHz. I think I've ...

15 30 50 per page