Linked Questions
19 questions linked to/from Location of Matched Filter
5
votes
1
answer
8k
views
Phase synchronization in BPSK
In BPSK for demodulation at the receiver end we do phase recovery between received wave and carrier wave. We can find the phase difference between the carrier and received waves using :
PLL
And ...
- 121
6
votes
2
answers
3k
views
Recovering signal for psk
I am currently working on a product (can't disclose too much details of the actual project) in which some data is being sent via audible (but on the higher freq) sound that is encoded with dqpsk.
...
3
votes
1
answer
5k
views
Gardner Timing Recovery for Repeated Symbols
I am implementing the Gardner Timing Error Detection algorithm for a QPSK signal. I understand the concepts behind it but I am curious as to what effect repeated signals can have on the phase lock.
...
- 45
2
votes
1
answer
2k
views
Symbol timing synchronization using a high sampling rate
Symbol timing synchronization usually relies on a digital PLL procedure, an iterative process that relies on detecting a timing error signal that is used to control an interpolation filter that in its ...
- 425
5
votes
2
answers
2k
views
Timing error detector used for symbol timing synchronization
The Gardner timing error detector is independent of carrier phase and frequency error, and is also quite immune to self noise (to my understanding, I may wrong about that). Can one assume that it is a ...
- 425
3
votes
1
answer
2k
views
Loop bandwidth for symbol timing recovery
I am trying to design the Symbol timing recovery (STR) block of DVBS Receiver.
How should I chose the loop bandwidth and damping ratio for determining the loop filter coefficients $k_1$ and $k_2$?
...
- 181
0
votes
1
answer
2k
views
Acceptable Carrier Frequency Offset for Specific BPSK system
I've been working to build a transceiver system, with details as follow:
Consists of Lime LMS6002D MyriadRF-1 board (RF front-end) and own-designed multi-proc SoC (baseband processor).
SoC is running ...
- 3
0
votes
2
answers
1k
views
Can we use Gardner timing error detector for multi level QAM or OFDM systems? [duplicate]
Sampling frequency offset (SFO) between the transmitter and the receiver in any system causes a gradually increasing timing error which is seen as an increasing phase rotation (function of time).
In ...
- 393
2
votes
1
answer
2k
views
Sampling signal after root raised cosine
I am generating series of 1 and 0. then pulse shaped them with root raised cosine and after than deciding to do match filtering and recovering the bits however it turns out that I am not getting the ...
- 353
1
vote
2
answers
1k
views
QPSK demodulator on GNURadio continuously loses phase lock
I am designing a QPSK demodulator to be used for receiving Meteor M2 (LEO satellite) signals (QPSK at 72Kbaud). However, I am finding a lot of problems in my way.
First of all, this is the flowchart I ...
- 157
1
vote
1
answer
955
views
GNU Radio Low Pass Filter doesn't work as expected with different transition widths
I'm new to GNU Radio and signal processing. I don't know if the following is a simple question, but I have been scratching my head about it.
I created a simple flow graph with a random source (0-3) ...
- 125
2
votes
1
answer
814
views
How to demodulation BPSK in real case(through a channel)?
I am configuring a channel sounding system. Using PRBS to correlate for time delay. Some details as follow.
Generate PRBS.
Using BPSK to modulate PRBS and Tx transmit.
Rx receive signal and ...
- 23
-1
votes
1
answer
654
views
Carrier frequency offset estimation for QPSK and asymmetrical spectrum
I am working on estimation of carrier frequency offset for QPSK data from a satellite. From my understanding, there are two main approaches: either remove data from the carrier (by taking the fourth ...
- 1
1
vote
3
answers
341
views
What is Self-noise in TED algorithm
I am working on a research project. The main task is timing error correction algorithm.
I start with studying algorithms which are exist. Currently I have read about Gardner TED algorithm for PSK ...
- 43
0
votes
1
answer
194
views
Which window function to use for QPSK signal?
I am trying to Receive a QPSK signal and for Sampling I need to recover clock. Now QPSK Signal is generated at 2.4GBaud. It is than sampled at 80GHz.Than further it is downsampled to 10GS/s (Symbols ...